Spill Kits and Spillage Control

Home Spill Kits and Spillage Control

Spill Control Product Range

General Purpose Spill Kit – PCDGK1

Clip close bag, quick response kit designed for smaller spills.

  • Kit contains 10 pads, 2 Super Socks – 8cm x 1.2m and 1 disposal bag & tie
  • Absorbs: 19 litres
  • Size: 43cm (h) x 52cm (w) x 10cm (d)

Battery Acid Spill Kit – PCDCK7

Battery acid will burn skin, eyes and any clothing that it contacts. This spill kit provides an immediate solution for many unexpected battery acid leaks or spills. UN approved polyethylene container will safely store damaged or leaking batteries.

  • Kit Contains: 60 Lt-Wt Pads, 3 Socks – 8cm x 1.2m, 2 Medium Cushions, 5 Litres Acid Neutraliser, 1 Dupont Chemical Splash Suit, 1 Pair Neoprene Gauntlets, 1 Pair Goggles, 2 Waste Bags & Ties, 1 Roll Caution Tape.
  • Absorbs: 45 litres
  • Size: 48cm (h) x 45.5cm (bottom diameter) x 58.4cm (top diameter)

Spill Control Maintenance Pads

For the purpose of absorbing most industrial type fluids including oil, coolant, cutting fluid, water and chemicals. Manufactured from high tensile strength polypropylene. Pads are dimpled and perforated down the centre for ease and economy of use.

Neoprene Drain Cover – PCDNDC1

Heavyweight neoprene drain cover with good resistance to oils and chemicals.

  • Wash and reuse.
  • Size: 1m x 1m

Tak Mat Multi Layered Floor Mats – PCDTM1

Protect floor areas that need to be kept dirt free with Tak Mat multi-layered floor mats. Effective super dust absorbent Tak Mats have 36 resin impregnated cotton covers enclosed in a heavy duty plastic frame. As one layer becomes dirty, simply peel back to reveal the next clean sheet.

  • Pack of 2.
  • 61cm x 91cm

Eez-Off Maintenance Wipes – PCDE07

General purpose maintenance wipes. Tough absorbent cellulose fibres with good wet and dry strength.

  • Resistant to solvents.
  • Excellent with oil, grease and water.
  • 400 sheets.
  • 30cm x 36cm

Caution Tape – PCDECRW

Caution or hazard warning tape for segregating areas of risk internally and externally.

  • Reusable
  • Red and white
  • 75mm x 100m

 

When working with Adhesives and Sealants or any bonding product, it is vital that the surface is cleaned correctly. Each surface needs to be free from dirt, grease and contamination prior to bonding. In some cases a primer may be required and it is critical that the correct primer is used. It may also be the case that light abrasion is required to help the bonding product key into the surface.

Due to the changing raw material content and surface finishes of some substrates, it is essential that all of our adhesives and tapes should be tested by the customer to ensure substrate and performance compatibility for each application. Please contact us for any advice. We do not accept any liability for product failure.

Find out more and Get a Quote Today

Contact Us
Product specifications referring to the mentioned properties are typical and do not imply specifications limits or guarantees.
These values may be changed at any time without prior notice. Please consult with Industrial Adhesive Solutions Ltd to confirm actual values.

The information reported in this webpage has been carefully checked and is believed to be accurate. Although it reflects our knowledge and belief, the Company will assume no responsibility for any errors or omissions, damage or loss resulting thereof. It is necessary to verify any recommendation for use as regards the suitability and conformity with actual project requirements, specifications and any applicable law.
0121 556 9900