Fraud Blocker

TensorGrip L40 – GP Contact Web Spray Adhesive

TensorGrip® L40 is a fast drying adhesive with good heat resistance suitable for bonding a variety of materials to sheet timber, metal and some hard plastics. Its tacky pressure-sensitive properties make it ideal for foam, fabrics, fibrous materials, some hard plastics and many other porous and non-porous substrates (to which immediate permanent bonds can be achieved by double-sided applications).

Advantages

  • Fast Drying.
  • Good Heat Resistance.
  • High Solids.
  • Versatile.
  • Easy Application Control.
  • Economic.

 

Description

Technical Information:

Viscosity: 300 cps 25°C sp#2, 30r.p.m.
Total Solids: 28.0%
Colour: Clear or Red
System Flammability: Non flammable adhesive in flammable propellant
Coverage: Approx. 75sqm bonded (150sqm total area)*
Shear: > 150 p.s.i.
Tensile (180° Peel): > 25 p.l.i.
Shear adhesion failure temp: (SAFT) 100gram> 105°C
Dry time: 2-3 mins dependant on temp & humidity
Open time: Long
Shelf Life: 18 months from date of manufacture

*figures quoted are approximate based on 16-20 dry grams/sqm in typical laminating applications

Download Data Sheet For Tensorgrip L40:

TENSORGRIP L40 SPRAY ADHESIVE CANISTER-English (UK & ROI) (13)
TENSORGRIP L40 SPRAY ADHESIVE AEROSOL-English (UK & ROI) (15)

Directions For Use:

This product is designed to be applied to two surfaces to be bonded together. Make sure that surfaces are clean, dry and free from dirt, dust, oil, loose paint, wax or grease, etc. For best results, the temperature of the adhesive and the surfaces being bonded should be between 60 degrees F – 80 degrees F (16degrees C – 27 degrees C).

Use with adequate ventilation. When possible we recommend shaking the canister well before using. Attach and secure hose tightly onto the spray gun with required tip. Attach the other end of the hose onto the canister. Make sure the hose-valve connections are securely tight. Open the valve on the canister slowly and fully, check for leaks during this process. Unlock the trigger on the spray gun to start spraying.

Prior to use, Check compatibility by spraying a small test patch of the adhesive on the substrate. This product may degrade some substrates. Spray about 10-20 cm (4” – 8”) away at a 90 degree angle to the surface, applying a uniform, even coat of adhesive to obtain 80% to 100% coverage of the surface. If necessary, spray another coat of adhesive in areas that appear to need more adhesive. Spray both surfaces to be bonded, one surface vertically and the other surface horizontally. Allow the adhesive to tack off until no adhesive transfers to the knuckle when touched.

Adhere surfaces and press together with adequate pressure. A roller is recommended to apply a uniform pressure to achieve maximum strength. Allow 24 hours for the adhesive to fully cure.

If the spray tip clogs, unscrew the spray tip from the gun and clean with solvent such as lacquer thinner or acetone. Do not use a pin on the spray tip orifice.

Handling & Storage:

CANISTER STORAGE/CHANGE OVER Turn valve on canister into the off position, spray out remaining adhesive left in the hose, disconnect the spray hose and gun from the canister. Reconnect the spray hose to a canister of cleaning solvent (sold separately) and spray out until liquid is clear which indicates that the hose and gun is clean. If you choose to leave the hose and spray gun on the canister, leave the valve on the canister open. Do not disconnect the hose/gun from the canister. Close and lock the spray gun.

For optimum results store canister above 18°C during use, but must always be above 10°C. Allow substrates to acclimatise to normal room temperature (18°C) for 48 hours before bonding. Do not exceed open time of the adhesive. Keep canister off cold concrete floors during use. If adhesive is expelled wet or as a jet, canister is too cold – move to warm environment and allow to thoroughly acclimatise before reusing.

CAUTION

  • Use only in well ventilated areas.
  • DO NOT thin or reactivate with solvents.
  • DO NOT incinerate. DO NOT expose to extreme heat over 50°C.
  • Keep away from sources of ignition. Release pressure before disconnecting hose.
  • Test for suitability before use.

MSDS and Technical Data Sheets MUST be read and understood before use. Information contained in this technical literature is believed to be accurate and offered in good faith for the benefit of the consumer. The company however cannot assume any liability or risk involved in the use of its chemical products since the conditions of use are beyond our control. Statements concerning the possible use of our products are not intended as recommendations to infringe on any patent.